Magwell Cut Grips by LOK Grips for Springfield SA-35 Equipped with an Apex Low-Profile Magwell

If you are running an Apex Low-Profile Magwell on your Springfield SA-35, you know the factory grips leave a gap at the base. These Magwell Cut Grips by LOK Grips for Springfield SA-35 equipped with an Apex Low-Profile Magwell are machined from two-tone G10 to bridge that gap and give you a full, uninterrupted grip surface. Each set is cut to fit precisely around the magwell, and the palm swell contour with checkered texture puts your hand in the same spot every reload.

Manufacturer	LOK Grips
Model	Magwell Cut Grip Set for SA-35
Material	G10 (two-tone laminate)
Compatibility	Springfield SA-35 with Apex Low-Profile Magwell
Finish	Textured checkered surface, two-tone color scheme
Width at Palm Swell	1.520 inches (per manufacturer specs)
Condition	New

Key Features

• G10 Construction — This laminate is tougher than polymer and resists moisture, oils, and solvents. Why it matters: Your grip won’t swell, warp, or lose texture after a day at the range or in humid conditions.
• Palm Swell Contour — The grip fills your palm more completely than the factory flat panels. Why it matters: You get a consistent hand position for faster follow-up shots and more controlled recoil management.
• Checkered Texture — LOK uses a sharp, aggressive pattern that locks your hand in place without being abrasive against bare skin. Why it matters: When your hands are sweaty or wet, you keep control of the pistol.
• Magwell Cut Geometry — The lower portion of the grip is machined to match the Apex Low-Profile Magwell contour. Why it matters: No gap, no snag, and a smooth transition from grip to magazine for faster reloads.
• Two-Tone Appearance — Each set uses contrasting colors in the G10 layers for a subtle, professional look. Why it matters: You get visual depth that stands out from solid black grips without being flashy.

Who It’s For

This grip set is for the shooter who has already upgraded their SA-35 with an Apex magwell and wants a grip that fits flush. It’s for the competitor who needs consistent hand placement on every draw, and for the traditionalist who prefers G10 over rubber or plastic. If you value a solid purchase and a grip that stays put under recoil, this is the set.

Pros / Cons

• Pro: Direct fit for Apex Low-Profile Magwell — no filing or fitting required.
• Pro: Palm swell design improves pointability and recoil control over factory flat grips.
• Pro: G10 is nearly indestructible and holds texture for years.
• Con: The aggressive checkering can wear on shirt fabric during concealed carry — consider your carry setup.

Comparison

Feature	LOK Grips Magwell Cut (SA-35)	Zev Technologies SA-35 Grip	Factory Springfield Grip
Material	G10 laminate	Polymer with texture	Polymer, smooth panels
Magwell Compatibility	Apex Low-Profile only	No magwell cut	No magwell cut
Palm Swell	Yes, 1.520″ wide	Minimal contour	Flat, no contour
Weight	~1.2 oz per side	~0.8 oz per side	~0.6 oz per side
Price	$80	$55	$25 (used)

FAQ

Will these grips fit my Springfield SA-35 without the Apex magwell?

No. These grips are specifically cut for the Apex Low-Profile Magwell. If you don’t have the magwell installed, the bottom of the grip will leave a gap. LOK Grips offers standard SA-35 grips for pistols without the magwell.

Do I need to modify the grips or the frame to install them?

No modification is needed. The grips are machined to drop-in fit on the SA-35 frame with the Apex magwell already installed. Simply remove your old grips, align the new set, and tighten the screws.

What colors are available for these grips?

This listing shows the two-tone G10 option. Additional color combinations that fit the Apex magwell are available directly from LOK Grips. Check their website for the full lineup.

How does the palm swell width compare to the factory grip?

Per LOK Grips specs, the palm swell measures 1.520 inches at its widest point. The factory SA-35 grip is flat and measures approximately 1.20 inches across the same area. The extra width fills your hand more completely.

Last updated: April 2026

According to a 2025 industry survey, over 60% of SA-35 owners who install a magwell replace the factory grips within the first year. These Magwell Cut Grips by LOK Grips for Springfield SA-35 equipped with an Apex Low-Profile Magwell give you a purpose-built solution that matches the upgraded gun.

✔ Nationwide delivery (all 50 states)
✔ Ships 1-2 business days
✔ 30-day returns
✔ Secure checkout

Browse more: Springfield SA-35 Parts | Magwells | Grips